Model Railroading – Wiring
Model railroad wiring is what makes the electricity flow in your train display so that the engine can pull its cars and so that houses, buildings and streetlights can glow with warm, realistic lighting. Modern wiring is even so sophisticated that it can run a miniature camera atop the engine as it chugs through your display. The possibilities are endless: Just think of all the electronics in real life and integrate them into your display.
Wiring Basics
Model railroad wiring can be a complicated endeavor; therefore, if you are new to wiring, it’s best to consider asking for help from a friend, consulting a resource book or even simply purchasing a pre-wired baseboard. However, a basic understanding of model railroad wiring will get you as far as you need to go when first starting out.
Controllers
One of the first components of model railroad wiring is a controller. Controllers, or transformers, run the voltage that determines the speed of the train’s engine. The controller also delivers the necessary power for accessories and can be turned on and off with a switch. On the controller itself, there are direct current (DC) terminals and alternating current (AC) terminals. The engines are generally controlled by the DC terminal, which can change the polarity so that the train engine can reverse direction. Accessories such as lights in houses or street lamps are usually controlled by the AC terminal, and wiring can run from underneath the board to each accessory as needed. Both DC and AC terminals are typically marked on the controller so that you can easily connect the wires.
Voltage
Another component of model train wiring is voltage. When installing lights and/or accessories in your display, make sure they are rated at the same voltage or slightly above the output of the AC terminals. For example, if you use a six volt bulb on a 12 volt terminal, the bulb will have a very short life. Also keep in mind that adding too many lights or accessories to the circuit can decrease the performance of your display, such as the train running more slowly than normal. In order to avoid overloading a large display, use two or more controllers as needed.
Digital Command Control (DCC)
With the digital age comes Digital Command Control, or simply DCC. This exciting advancement in technology enables an operator from a “command station” to feed the track a digital signal; this signal provides both power and control instructions to the locomotive which reads it with “mobile decoders.” One advantage of this protocol is that two locomotives on the same electrical track can be operated independently. DCC can also be used to control other accessories.
Avoiding Electrical Mishaps
Sometimes it may be inevitable to avoid mishaps when working with your model railway wiring; however, following a few basic practices can help improve your success. First, make sure that all connections are correctly wired and tight, as loosely fitting wires may not properly perform. Also, ensure that your train tracks are connected to the DC terminal on your controller. For most trains, if you mistakenly connect the tracks to an AC terminal, you may possibly damage your train’s engine.
Furthermore, to maintain continuity of your track and to support efficient wiring, make the track as level as possible and secure it to your baseboard. Debris like dust and dirt will accumulate over time, which can kick up inside of the train’s engine and may interfere with performance. Therefore, occasionally clean the track with a soft, clean cloth using a contact cleaner or denatured alcohol. Keep in mind that denatured alcohol is highly flammable and poisonous; therefore, use extreme caution when handling.
About the Author
Johan became fascinated with trains when he was a toddler. “My mom took my brother and me on Stone Mountain’s Scenic Railroad. In those days they still operated a steam locomotive. I loved that old fashioned smokestack!” Blushing, Johan added, “And I was devastated when I learned my engineer dad didn’t operate trains.” For more information and to join a fun community, please visit Model Railroading for Beginners.
Bachmann Digital – Fitting a DCC Decoder
|
|
Bachmann Trains Digital Commander Ready – To – Run DCc – Equipped Ho Train Set $167.08 Model railroading enters the digital age with the Digital Commander! Create your own fledgeling railroad empire or work with a friend to coordinate freight and switching operations. Our exclusive E-Z Command digital control system lets you independently control the speed, direction, and lighting of two decoder-equipped locomotives.Features include: •DCC-equipped EMD GP40 locomotive and EMD FT… |
|
|
MRC Tech 6 Sound Controller 2.0 $82.56 MRC?s amazing Tech 6 DC Power Pack gives railroaders full control of any sound decoder equipped locomotive. The Tech 6 combines MRC’s legendary power pack technology, reliability & control, with our world beating BlackBox. Operate either Analog DC locomotives, or fully functional dual-mode sound decoder-equipped locomotives, or any DCC decoder equipped locomotive. With 2 amps of power, it can hand… |
|
|
Bachmann Trains EMD DD40AX Centennial DCC Equipped Diesel Locomotive Union Pacific #6910 $73.14 The latest in DCC monster locomotives. In 1969 UP received the EMD DDA40X, a dual-engined, 6,600-horsepower road locomotive. They were dubbed the Centennials in honor of the 100th anniversary of the completion of the first Transcontinental Railroad. DCC ON BOARDTM locomotives feature dual mode digital command control decoders enabling operation with a standard DC analog power pack or any NMRA-… |
|
|
Basic DCC Wiring for Your Model Railroad: A Beginner’s Guide to Decoders, DCC Systems, and Layout Wiring $9.66 A beginner’s guide to decoders, DCC systems, and layout wiring. Author: Mike Polsgrove, full color, 55 pages.The Trainz SKU for this item is P11592843.Condition: NewTCA Grade: C-10Original Box: YesManufacturer: KalmbachProduct Number: 12448The Manufacturer’s Suggested Retail Price (M.S.R.P) for this item is $15.95…. |
